Cleaning your kitchen mixer tap: how to make your mixer tap shine

A housewife cleans the mixer tap with a microfibre cloth

Kitchen mixer taps require regular cleaning: as they are in daily contact with water, limescale can quickly form on the surface. The aerator, the fine-meshed sieve on the outflow, can also become clogged up with limescale deposits, which can cause the mixer tap to start spraying. The following care tips will help you to avoid these problems effectively, so that you can continue to enjoy a shiny tap for a long time to come.

Preventing limescale marks properly

When turning off your mixer tap with wet hands after working in the kitchen, you almost always leave drops of water on it. These dry and leave limescale behind. Visible limescale can form quickly, particularly in regions that have hard water. The term ‘hard water’ refers to a high calcium bicarbonate content in water. Hardly any limescale occurs below a hardness of 4. If you have hard water, you should therefore rub the surface dry with a microfibre cloth after each use, if you don’t want to be constantly cleaning your mixer tap. This will allow you to extend the intervals between regular cleaning.

Removing limescale gently

If limescale has formed, it is best to treat this with a mild, organic acid, e.g. a solution of acetic or citric acid. Important: before applying the substance, check whether your surfaces are resistant to acids. Marble and aluminium, for instance, should not be cleaned with acidic substances. Many plastics and varnishes are also sensitive to acid. As the owner of a BLANCO mixer tap in Stainless steel, Silgranit look or Ceramic look, however, you’re good to go: if used correctly, these materials tolerate cleaning with acetic or citric acid without any issues. Instead of acid cleaners, you could use a mild descaling spray, such as BLANCO Antikalk. This limescale-removing agent has been specially developed for BLANCO mixer taps and sinks. It cleans gently yet thoroughly.

To remove limescale, apply the cleaning agent to the soft side of a sponge and wipe the mixer tap thoroughly. Be sure not to leave acid-based cleaner on for longer than indicated on the package instructions. Avoid lengthy, vigorous scrubbing with the rough side of your sponge. This can scratch your mixer tap. Rinse your mixer tap down with clean water and rub it dry with a microfibre cloth.

Cleaning the aerator

Over time, hard water can cause the water flow through the mixer tap, and especially the aerator, to become clogged up. The aerator, also known as the jet regulator or stream shaper, is the nozzle on the outlet of the faucet. If this closes due to limescale deposits, the outlet may spray water uncontrollably in all directions when the tap is turned on. For this reason, you should clean the aerator at regular intervals.

Acetic and citric acid work well for this purpose, too. Moisten a sponge with either kind of clean and spread it over the fine mesh at the outflow of the mixer tap. An old toothbrush will allow you to give it an even more thorough clean. In most cases, the limescale will dissolve, giving you a neat spray once again. BLANCO spray heads also have practical anti-scale nubs on the aerator, which significantly reduce limescale formation and enable easy cleaning.

Removing stubborn deposits on the aerator

If the limescale is very hard, you should give the aerator a thorough clean. Many BLANCO mixer taps allow you to simply unscrew the small nozzle anti-clockwise. You can then steep the jet regulator in vinegar water or citric acid overnight. Next morning, rinse away the loosened limescale remnants and reattach the aerator by screwing it in clockwise.

How to look after your pull-out spray

A mixer tap with a pull-out spray is highly practical, as it allows you to reach even the furthest corners of your sink with ease. Vases and tall-sided pots are easy to fill up. But what if the hose no longer slips back easily into its holder? If this happens, apply some fitting lubricant to the moving parts of the hose. The hose will then glide back smoothly into its original position. Having a hose guide in the base cabinet is particularly practical, as it prevents the hose from becoming hooked on things or twisted within the cabinet.

Supplement your mixer tap with a dirt filter

You can also protect your mixer tap by installing the BLANCO dirt filter. This is particularly recommended in old buildings and for old pipes. The small metal mesh filters out dirt particles that come from the water pipes, thus preventing your mixer tap from becoming contaminated. It is fitted between the angle valve – the valve for the water supply beneath the sink – and the connecting hose for the mixer tap. If you have high pressure, you can attach two filters, one in front of the other, while one filter will be sufficient for low pressure.

You can get your mixer tap shining with the right care and cleaning.

Try out the BLANCO cleaning and care agents!

BLANCO Antikalk:
BLANCO’s Antikalk spray ensures that you’re doing it right. The formula was specially developed for BLANCO sink and mixer tap surfaces. It cleans gently yet effectively.

BLANCO key for jet regulator:
if your mixer tap model requires a cleaning key for the aerator nozzles, you can order the right model easily from our spare parts shop.

BLANCO dirt filter for angle valve:
supplement your BLANCO mixer tap with the right filter to avoid damage.

Share us via